Quantcast
Channel: Intel Communities : All Content - Desktop Boards
Viewing all 4931 articles
Browse latest View live

S1200SPL and RAID1 "On Request"

$
0
0

Intel Server Board S1200SPL.

В режиме Intel RSTe 4 RAID1 есть ли режим обновления тома "По запросу", как в более ранних Intel Server Board?

Этот режим необходим для защиты от воздействия вирусов.

Есть ли такой режим (RAID1 с ручным обновлением "По запросу") в режиме Intel ESRT2?

В описании ESRT2_Software_UG.pdf об этом ничего не сказано:

http://www.intel.com/content/www/us/en/support/boards-and-kits/000005760.html

http://www.intel.ru/content/www/ru/ru/support/boards-and-kits/000005760.html


How To Make DZ87KLT-75K Fully Compatible With Haswell Refresh e.g. (Core i7-4790K Devil's Canyon)

$
0
0

I figured out how to make the DZ87KLT-75K fully compatible with Haswell refresh, in this post i confirm with a Core i7-4790K Devil's Canyon runs perfectly on the motherboard, short story is i had an i7-4770K initialy and happend to be in a position that allowed me access to the i7-4790K brand new boxed since i got it to work its now my main CPU in the DZ87KLT-75K

 

Before the steps as we all know the Haswell refresh CPUs are detected correctly in any 8series board by Intel, so what causes them not to function correctly is the Intel Management Engine (Intel ME), intel decided not to update the ME while updating BIOS, so the trick is just to update the Intel ME to aversion that come around same time as the Haswell refresh.

 

Steps

Assuming you have downloaded all the correct required files

 

1. I installed Core i7-4790K

2. Switched on PC booted into windows

3. I then followed steps to install

 

Intel ME 9.0 Consumer 1.5MB Firmware v9.0.31.1487

 

using this tool

 

Intel FWUpdate Tool for ME 9.0 Firmware v9.0.22.1467

 

I used the win tool in windows not dos

 

Everything went well shut down the PC then powered on again and all was well, restarted several times, even tinkerd with memory settings saved several times, run a stability test for 8 hour and all was ok

 

Intel ME files are found on this website along with all the necessary tools and instructions

 

http://www.win-raid.com/t596f39-Intel-Management-Engine-Drivers-Firmware-amp-System-Tools.html

la carte DG965WH est-elle Windows 10 compatible?

$
0
0

I cannot install Windows10: installation stops after hours and hours.
Is my DG965WH Windows 10 compatible, or is it necessary to update its driver?

 

Thank you

Ghislain

Chassis Intrusion; Asks for Password; Cannot Reset Bios - DH77KC Motherboard

$
0
0

Hi! My name is Alex and this is my first time posting here, but has been around for a long time looking for solutions. And regarding my problem, I know there is a lot of threads about it, I've read almost all of them, but none of them worked for me. I already tried contacting Intel, but their solutions are the same with what I tried.

 

Anyway, back on topic.

Last weekend, I decided to clean my CPU for first time in a year, and opened the front and back case. When I turned on my PC, a warning showed up saying "The following warnings are detected during this boot. These can be viewed in the Setup in the event log. WARNING: Chassis Intrusion". The warning shows up just after Intel Logo shows up where you can press F2, F7, and F10 for BIOS Setup, BIOS Update and BOOT Settings respectively. The problem is that after the warning, it asks for a BIOS password, which I have forgotten a long time ago (can't even remember setting it) and I cannot bypass this warning by pressing F2 to go straight to BIOS settings. I tried entering blank, 123456, and other default passwords I find on the web.

 

I have already tried removing the 24-pin motherboard ATX power connector and 4-pin CPU power connector then removed the battery for almost a day and put it back in; the BIOS settings did not reset; also tried setting the Jumper to pins 2-3 (CFG) from pins (1-2) BIOS to configure the BIOS on boot up, but the Chassis Intrusion warning still takes over, asking for a password. And lastly, I also tried putting a jumper on the Chassis Intrusion header (It's composed of 2 pins only.) Still didn't work.

 

My guess is that, as long as the Chassis Intrusion event is still recorded in the BIOS event log, I can not do anything unless I type in the damn password.

 

Sorry for the lengthy post, I just want to get into details to avoid getting another solution I tried already and I really need my PC to work again to start practicing C++ and learn programming. Any OTHER ideas? Any other input would be very much, greatly appreciated. Thank you very much!

Troubleshooting Wake on LAN on DZ77GA-70K Windows 7 x64

$
0
0

I tried several ways to setup WOL on my DZ77GA-70K Windows 7 x64 system on 82579V LAN interface. The closest solution is to leave on Power Management tab only “Wake on magic packet” checked – other options unchecked. Driver version is 12.10.28.0. (after installation of LAN_Win7_64_PROWin_19.1.exe) From another PC I sent packet with special tool that sent packet with MAC. This cause my computer getting awake from s3 (sleep). But this work only about several minutes after getting sleep. After about 10 minutes computer does not response and stays in Sleep mode (it’s possible to turn it on by pressing keyboard button). I think the problem is something related with DEEP sleep – I think PC turns off some LAN components after several minutes. How to disable this Deep Sleep? Or what is the way to use Wake on LAN on this mainboard?

 

Power.png

Is it possible to connect NVidia GForce GTX295 using SPIDF 2 pin cable directly to D975XBX2 motherboard to get audio on HDMI when i connect it to a HDTV?

$
0
0

Is it possible to connect NVidia GForce GTX295 using SPIDF 2 pin cable directly to D975XBX2 motherboard.

 

I'm trying to get video and audio over HDMI cable when I try to connect my PC with a HDTV.

 

Thx in advance!

Intel DX58SO2 No POST - Blank Screen

$
0
0

I am a newbie so this could be something really simple. I purchased this board to replace another mobo that had a bad USB chipset. All components (HD, video card, CPU, DVD ROM. PSU) were all working fine on other motherboard - just USB chipset was shot.

 

After installing the new board and powering up the PC, I do not get any display. The monitor doesn’t seem to receive any signal. The 80h POST code displayed is 14 (according to the manual that is LAN init).

 

Here is what I’ve tried so far:

-checked the CPU for bent pins

-reapplied thermal grease

-replaced all mobo screws and case studs

-tried the PCI-e video card in each of the slots

-pulled all the RAM out and tried to boot (no error beeps...this really concerns me because I was under the impression that I should get some beeps)

-swapped HD SATA cable to other SATA ports

-removed and reseated the CPU and motherboard

-disconnected and reconnected all power cables

-rechecked all cables are connected to the mobo correctly

 

Can someone please offer some assistance?

 

Thank You!

Intel DH87RL black screen with GTX1080, windows 10 runs fine

$
0
0

Hi,

 

I recently changed my dedicated graphics card on my Intel DH87RL motherboard with i7-4771 CPU. My new card is a Inno3D Geforce GTX1080. My old card was a Asus GTX970.

With the new card, my monitor shows no signal while booting to windows. The first visible thing on the monitor is the windows 10 Logon Screen.

The monitor is connected via Display Port.

Whats wrong with the bios or the settings? I use the latest bios. Without the Nvidia card, the integrated graphics works as usual.

 

tia,

 

Andreas


i need ***.bio file for d101ggc to upgrade my bios please give me a link

Mejorar el procesador

$
0
0

Tengo:
Intel® 945P Express Chipset
EM64T
http://ark.intel.com/es/products/27723?wapkw=chipset+945p&_ga=1.116950662.1403967990.1468603564#@compatibility

Y el procesador:
Intel® Pentium® D Processor 830
ID 0F44
http://ark.intel.com/es/products/27513/Intel-Pentium-D-Processor-830-2M-Cache-3_00-GHz-800-MHz-FSB


El procesador siguiente mejoraria mucho al PC, seria compatible, en qué se mejoraria, cuánto?
Intel® Core™2 Extreme Processor X6800
http://ark.intel.com/es/products/27258/Intel-Core2-Extreme-Processor-X6800-4M-Cache-2_93-GHz-1066-MHz-FSB

http://ark.intel.com/es/products/27723?wapkw=chipset+945p&_ga=1.116950662.1403967990.1468603564#@compatibility.


Cuando se dice:
Tamaño de memoria máximo (depende del tipo de memoria)  4 GB

¿Eso significa que se podria poner mas memoria?

Intel DZ87KLT-75K irritating issue

$
0
0

Before anything else, this is my rig.

 

4770k

kingston hyperx predator 2400mhz - stock speed under xmp 1.3 (4x4gb)

cm 750w psu

gtx 980ti

windows 10 home x64

 

Hi,

 

I have gotten this board with a sale 2 weeks ago. everything seems to be working fine. updated the bios to 0457 with the 4770k and boots just fine.

 

But then with this bios, everything that I save as a setting gets saved other than processor speed in which i tried setting it to 4.2ghz then it goes back to 3.9ghz in the bios as well as in windows. plus whenever I tried to set my memory stock speed to 2400mhz, it does not boot. it goes from post then off then post then off, same issue that I have read with the bios memory issue since the board came out.

 

its irritating as hell believe me, wasted 3 days of my time off leave for nothing.

 

I tried downgrading to 0453 because i cant get anywhere with the irritating "most updated bios" then things started to work. everything goes well and i was able to overclock to 4.2ghz without a problem so what am i saying as numerous issue?

 

i tried setting the ram to its stock speed of 2400mhz and boots just fine and i was able to use my PC but whenever i tried to download something like ANY SOFTWARE, it says network problem then i went ahead and check if anything was a miss from the device manager so i checked on the drivers then everything looks good. i tried updating some games that are NOT on steam because they had default launchers like heroes of the storm from blizzard and world of warships from war games and the same problem happens wherein it does not want to update the file because it keeps on saying that there is a failure in extracting the package. so my mind was blown and I cannot seem to know where the problem is. i reformatted like 5-6 times and was up for more than 36 hours just trying to fix this board.

 

finally when i was about to give up, I tried lowering it to 2133mhz with manual timings which is also based on the XMP profile and everything went fine including downloading software and updating games.

 

So my question is:

 

1. why does the 0457 does not work on the board?

2, bios 0453 is the only bios i can go to and seems to me that all this madness is pointing towards the bios support for the memory?

3. me and my friend bought the same board but his was able to update to 0457 and was even able to use a gskill trident memory to go as high as 3000. bios faulty again?

4. i tried re-updating to 0457 and its much much worse than before as my mouse does not even work anymore with it. luckily flashing back to 0453 only needs a keyboard. a faulty board or again, bios?

5. It should support 2400mhz according to the website as i saw somewhere but then why this does not work?

6. how to solve this issue?

 

Thank you for the help in advance. hopefully somebody can shed some light.

DX58SO RAM Issue

$
0
0

I have a DX58SO motherboard that I have been running 12G of Corsair Vengeance DDR3 1600 Mhz in a triple channel configuration. This had been up and running for nearly a year. This weekend, I took the system apart to changed out the cpu cooler. Now that I have reassembled, it refuses to POST with all three RAM modules installed; it gives 3 error beeps at startup which indicates a RAM error. It will POST just fine with two modules installed in the dual channel configuration. I have swapped out modules and all 3 will work in dual channel but it will not POST with any of the 3 in Channel A. As per the user manual, I am populating all 3 BLUE RAM slots for triple channel and the furthest from the CPU 2 BLUE slots for dual channel. Did my Channel A just crap out or is there something I am missing?

Does the DQ67SW have a UEFI bios?

$
0
0

Hi there! Does the DQ67SW have a UEFI bios? I recently purchased RAM that only supports motherboards running a UEFI bios. :\

 

Thank you!

DQ45CB Possibility to upgrade Option ROM?

$
0
0

Hi,

 

I have a DQ45CB Mainboard. To get better Windows 10 Support (I know it has no official Windows 10 support, but it does work)

I want to upgrade the Option ROMs inside. (And get support for HDD >2TB)

 

In BIOS 0133 are inside:

RAID Option ROM 8.6.0.1007 and 8.5.2.1002

Intel Boot Agent GE 1.3.65

vBIOS 1940

Management Engine BIOS 5.2.40.1037

 

For the Components exists newer versions (found in other Forum)

RAID Option ROM 11.2.0.1527

Intel Boot Agent GE 1.3.72

vBIOS 2085

Management Engine BIOS 5.2.71.1048

 

Is there a Possibility to upgrade all the ROMs or a fiew myself? (Especially the RAID Option ROM)

 

The BIOS support UEFI boot. Does the Board support secure boot too??

 

Thank you for help!

Update for Intel(R) HD Graphics 4600 keeps failing with error code 80070103

$
0
0

Windows Update (on Windows 8.1) is trying to install an update for Intel(R) HD Graphics 4600 and it keeps failing with error code 80070103. I have tried to contact with Microsoft, they advised to download that driver from Intel, I’ve done it. But it’s failing with the same error code 80070103. I would be grateful, if someone could help? Microsoft said that the error related to Intel product.


DG41WV + Nvidia HD Audio

$
0
0

Card: Geforce 210

Motherboard: Intel DG41WV

CPU: Intel E8400

OS: Win 8 Pro

TV: HDMI output to Samsung TV

 

The end user said they disabled the HD audio in the playback devices, since then nvidia HD audio is MIA

 

When the TV is connected it shows up in the nvidia control panel under the Set up digital audio, but no audio goes through.

 

Tried clean driver install, when running the geforce custom driver installation it doesn't even give the HD Audio option.

Computer does not detect the HD audio component of the card.

Tried with different nvidia cards(anoter 210 and a 630), same issue.

Did a fresh win7 install on diff HDD same issue.

Replaced Motherboard(same model), same issue.

Replaced RAM, same issue.

Replaced PSU, same issue.

Replaced CPU, same issue.

 

Tested card on different PC works fine.

 

Any ideas what could be causing this?

USB Boot DQ67SW Motherboad

$
0
0

I want to know what is required to boot from a USB thumbdrive on the DQ67SW board? I'm pretty sure I've done this before, but it will not work now. The thumb drive is in fact bootable as I've booted it from other PC's just fine. I tried using every USB port but is does not make a difference. I also tried disconnecting all SATA drives to force it to boot from USB, but then I get the error message stating "no bootable device found". Seems that it does not want to boot from USB.

 

In the BIOS I have USB boot enabled, boot from removable devices enabled and UEFI boot disabled.

 

Are there some specific, different requirement for the USB boot device?

 

Thanks.

Wie ist das Standard Passwort für Intel ME

$
0
0

Ich kann nicht auf das Intel BIOS zugreifen.

Wie ist das Standard Passwort für Intel ME?

I am in need of a Desktop Board E210882 LGA775. Does anyone have a suggestion where I could purchase one?

$
0
0

I am in need of a Desktop Board E210882  LGA775. Does anyone have a suggestion where I could purchase one?

HyperX Fury 8gb Hx318c10fb/8 running on Intel DP67BG up to 32gb

$
0
0

Hi everyone

I want to update my system up to 32gb RAM (4x8gb), my motherboard is an Intel DP67BG, theoreticatly it supports:

 

• Four 240-pin Double Data Rate 3 (DDR3) SDRAM Dual Inline Memory Module (DIMM) sockets with gold-plated contacts arranged in two channels

• 2133 MHz to 1066 MHz DDR3 SDRAM Memory Modules
• Support for single- and dual-channel memory interleaving
• Unbuffered, non-registered single- or double-sided DIMMs with a voltage rating of 1.65 V or less.
• Non-ECC DDR3 memory
• Serial Presence Detect (SPD) memory only
• Up to 32 GB maximum total system memory using 8 GB DIMMs

 

I was told that the Kingston HyperX Fury 8gb DDR3 1866Mhz 240-pin (model no. Hx318c10fb/8) is compatible with the DP67BG, but i can't check it anywhere.

 

Can you tell me if these are compatible and work well with 32gb RAM (4x8gb)? I want to check that the HyperX model I mentioned is Non-ECC and is in fact a SPD memory.

 

Thanks in advance.

Viewing all 4931 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>