On my new Dell Optiplex 7010, I have an Intel Core i5-3470 CPU @ 3.20GHz – this is a genuine quad core processor with hardware virtualization - but the Dell machine is somehow blocking the hardware virtualization.
Please go to this thread on these Intel forums and let me know if you have the answer -
Hardware virtualization is blocked in Win 7 Pro 64-bit Dell machine - what to do?
I am posting here in case it is a problem with the Desktop board.
Thanks, and Happy Thanksgiving Leftovers.
I have an intel board DH87MC when i turn iton it doesn't boot from first attempt.
When i try again i got : "BIOS has detected unsuccessful POST attempt(s)... Press "Y" to enter Setup or "N" to cancel and attempt to boot with previous settings.". When i press N the pc restart and works normally.
I tested many Hard disks , power supplies , and rams same problem.
Please help me.
Thanks
Attached you can find the error..
To whom it may concern,
You may not know it, but there is a rapidly growing movement of people trying to make an open-source BIOS. In fact, they've already succeed for many motherboards. You can get more information at coreboot.org.
I know that if you open source your BIOS, then other companies will copy you, and for this reason I do not ask that you do that. If you open-sourced the BIOS only once it has reached end of life, you would not be giving up valuable intellectual property, and you would increase your reputation within the open-source community.
Yours sincerely,
orthogonal
i bought intel dz68db motherboard and attached my processor corei5 2310
But there is some issue no display
I have changed dvi connector two times
But problem is same
It shows check dvi cale
What should i do
Okey here is the bug, my computer (board is DX79SI with last BIOS v0650 for to day) turned off, I plugged my Transcend TS32GJF760 USB 3.0 (with Windows 8.1 on it) into USB 3.0 port and I turned on my computer, so I see blue screen of BIOS and that is all. Computer stuck forever. My mouse and keyboard are USB 2.0 and they plugged into USB 2.0 ports not responding, mouse doesn't have red light of laser. I tried to plug Transcend into USB 2.0 port and booting was fine. So the bug is definitely in chip Renesas\NEC UPD720200 Controller OR in BIOS, so can you fix it somehow?
Second question, is why you not updating Driver for Renesas\NEC UPD720200 Controller to version 2.1.39.0 ? On the page of this board still old version 2.1.28.1
hello, i have this motherboard with 3820 cpu onboard.
the only thing i have is some blinking leds, error codes and nothing more. no video.
i am sure i have to change bios, but i can't afford to buy 3930k or similar.
i can instead easily reprogram bios chip directly, i already detached it and put on programmer, it is good, readable and dumped content on a file.
winbond 25Q64CV,
i can't extract bin file from bio, can anyone provide me the correct file, like 430 or higher?
thank you
sergio
.
Hi, I am trying to dowload a BIOS update for a very old Intel motherboard at
I'm trying to download the MJG4110H.86A.0008.EB.EXE file, although this is happening with all the files on that page. If I click on the file to download it, an license agreement is displayed, when I click on the "I Accept the Terms of the license agreement" nothing happens. I can't get past it to download the file. I've tried firefox and IE, same problem. Is there an FTP site or some other way I can download the file? Thank you!
I'm running Windows 7 Pro x64 on DX58SO with Intel Rapid Storage Technology, version 12.5.0.1066, three Disk RAID 5. I had a disk, Seagate Barracuda ST3500320AS 500GB, fail and got an indication from the RST icon in the notification area. I replaced the disk and the SATA Array is currently rebuilding and about 60% complete. However, when I open the Intel Rapid Storage Technology program, I see four disks, three show status as normal and one phantom disk, status missing, port location: unknown. It also shows the serial number of the old disk with a colon and zero added, but nothing else. I'm hoping that this phantom disk will disappear when the SATA Array finishes rebuilding, but I don't get the impression that it will. Also, on the Status tab, of the RST program, the current status indicates the system is reporting one or more events, and data may be at risk. It then indicates to refer to the details below for more information. There are two events indicated. The first is that the SATA Array 0000 is rebuilding and the second is "Unknown disk on Controller 255, Port Unknown: Missing.
Will this missing phantom disk issue resolve when the system finishes rebuilding the SATA Array after replacing the failed disk?
Thank you in advance for your assistance.
Regards
I am assembling a desktop. My system configuration that I have purchased is :
Motherboard: DH87MC
Processor: i5 4440
Ram:Corsair Vengeance DDR3 4GB Ram (CMZ4GX3M1A1600C9)
After assembling, (did it exactly as mentioned in the integration sheet), immediately the second I pressed the power ON switch, the processor hot LED glows with a beep sound , the processor fan starts and stops immediately, and the system turns off. Nothing happens after that, only the power on green LED keeps glowing. I have changed the SMPS with another one from my old desktop which is OK, and the same problem appears. I am at a loss. Is there any problem with the motherboard or processor or some other problem? I have connected all the connectors as per the manual, and the connectors can't mismatch. Please help, I have got lot projects to start, need a 64 bit system immediately, just stuck up here.
Can I run Windows 8.1 on a D975XBX2 board and do I need any updates? PeterBull
ok, I got this board and 3820 and yes, they still sell it with out BIOS !! Intel you should recall those,
anyway now, too late, I took the setup overseas and have no access to supported CPU
I need a BIN format for new DX79SI bios file in order to program the chip directly, I have the tools and knowledge to do so,
but the downloadable intel format is .BIO
any ideas ?
Regards
Estou com problemas na minha placa mãe onde a mesma só reconhece a memória na bios, mas quando vai carregar o sistema operacional (Windows 7 x64) aparece um erro devido ao pente ser de 4gb. Eis a minha dúvida, se a placa mãe suporta até 16gb, porque não está funcionando com o pente de 4gb?
Tenho 2 pentes de 2gb da Kingston KVR133303N9/2G (que funcionam normalmente) e tenho 1 pente de 4gb da Corsair CMV4GX3M1A1333C9 (que não funciona). Gostaria de saber o motivo. Ps.: Já atualizei a bios e não resolveu
Hi,
I have a used DH67BL board. The previous owner already used it with this failure.
The problem: in every start, it writes an intrusion message.
What I did:
- newest bios, it was earlier
- clr cmos
- intrusion header is open (by the manual, the opened case closes it)
- intrusion header pins: grnd ok, signal 2,93 volt - seems to be ok
- in bios, in configuration, event log deleted, logging disabled, in security intrusion: disabled
- cmos battery ok
- CPU: G1620, the previous owner used it with an i3-2120
- RAM: 1x 2gb
- tried to close the intrusion header, too
But the problem is still not solved.
Any idea?
Thanks
Hello,
Intel motherboard dq87pg ignore/corrupt all UEFI BootXXXX/BootOrder variables except last one set.
So if you install Windows then Linux you've got in boot menu (F10) only Linux (grub) and if you installed Linux then Windows you've got only Windows Boot Manager by F10.
It appears to be worked well only in origin firmware ver. 0030, but in 0035,036 it was broken by ignoring UEFI variables. Also if you reflash the same motherboard (0035/0036) with both installed Win/Linux with origin 0030 firmware you've got all announced OSes in boot menu (F10) back(!). So it's just ignoring then and seen then only in ver. 0030
Version 014x corrupts previous set BootXXXX variables when you set new one. When you set new BootXXXX var via efibootmgr it's ok, but when you reboot and check it again with efibootmgr -v, you will see corrupted device path in all variables. So you've got again only one OS in boot menu (F10)
Also it's reproduces for all four motherboards in my hands
Today I updated the Intel DQ965GF board in my htpc to the latest BIOS (old one was from 2006) and now it doesn't boot.
I tried flashing in DOS but it would just hang on a blue screen (might be something to do with AMT security), and when I tried flashing in Windows it told me to reboot, and when it went down and came back up I got nothing. I got a blank screen for a few seconds and then no signal.
I try doing the BIOS recovery (via jumper) but I get no signal for about 5-10 minutes until I get a blank screen. Usually there should be things going on here like the illustration on Intel's site, but there is nothing. I tried two romfiles, a SATA drive, an IDE drive, DVD, CD, USB flash drive, FAT32, FAT, NTFS, everything. I could only get it to go to the blank screen with a USB flash drive (even though the manual said CDs)
Not many blinkenlights which is a bit worrying.
Help *very* appreciated (as usual)
inb4 "Spend $300 and buy a new CPU+board+memory"
I have an intel board DH87MC when i turn iton it doesn't boot from first attempt.
When i try again i got : "BIOS has detected unsuccessful POST attempt(s)... Press "Y" to enter Setup or "N" to cancel and attempt to boot with previous settings.". When i press N the pc restart and works normally.
I tested many Hard disks , power supplies , and rams same problem.
Please help me.
Thanks
Attached you can find the error..
Hi,
I'm using a DQ670W motherboard as a VMWare ESXi whitebox for my personal use. It works great with ESXi up to 5.1U1.
ESXi 5.5 has been released but it hangs on ACPI initialization on startup or install. Searching on google, other brands of motherboards are facing the same problem, they released a new BIOS update to make ESXi 5.5 work even if their motherboard are not officially supported by VMware.
Is Intel aware of this problem ? Will a BIOS update be released ?
I can provide technical information for investigation.
Rene
I'm using Intel XTU and when i look at the graph, i see power spikes in the voltage of the graphics card.. what is this and what should i do about it??
the blue spikes are the graphics voltage - it goes from 0.0 to 0.9volts just randomly and right back down to 0.0. you can see here pictured below. .its the spikes.. I'm not playing games or anything during this..(the blue big spikes)
Does any know if/how you can boot into a UEFI shell on an intel DH67BL MB? I need to flash an LSI raid card in UEFI.
Thanks
usiung Dextop board DH87MC since last 1 year almost, but from last month I am unable to install the HD graphics driver (ever sin ce i replaced my crashed HDD) also, my DVI port of the mother board is not working since then., Hi, I am usiung Dextop board DH87MC since last 1 year almost, but from last month I am unable to install the HD graphics driver (ever sin ce i replaced my crashed HDD) also, my DVI port of the mother board is not working since then.
Can any one please tell me what is to be done?????