Hi friends,

I am currently running out of ideas to find the reason for my RAID 5 Performance problem with the IRST system. May be someone can help me.

I got  a GA-H57M-USB3 Board , because it seems to be a good choice for a low power PC in combination with the i5 650 when using the build in GP of the CPU. Also it should support RAID5 for the Intel SATA Controller, so I hoped to replace my “energy eating” Synology DS508 RAID system as well.

The board is running fine and power consumption is nearly as expected, but the problem is that the RAID5 mode seems to be useless because it is extremely slow.

On different sides I found a lot of threads regarding the RAID5 speed problems with the IRST software and some of them seem to be fixed. But none of these tips fixed my problem.

I currently use 4 x 1TB 2,5” Toshiba disks. I had ordered 6 but 2 of them did not pass my tests with the smartctl utility.  Installed is the latest driver version from the Intel Download side (10.1.0.1008).  Used Software: Win-7 64 Bit(Business), smartrctl, ATTO Disk Benchmark.

Win7 is installed on a single SSD which is connected to the first SATA port of the other SATA Controller. This should make sure that the RAID system is in power safe mode, most of the idle time.

For the RAID5 Problem I made the following tests:

-          Disabled Array and checked all disks in single mode: Read and Write speed was between 80 and 100 MB/sec

-          Read/Write checked the single disks(not array configuration) by copying 100 GB of data across. All fine. So hardware and cabling must be fine.

-          Used only 3 disks in the array (idea: 2TB limit) . Does not fix the problem.

-          Played around with different stripe sizes. No change.

-          Double checked the disks with smartctl

Currently the “Initialization” is running, but after 24 hours it has just reached 30%. I do not believe that this is normal?
And do not believe that this will fix the problem.

I think I must not say that this test needs hours :-(

Grettings

hi everyone,

hope you'll understand my problem,my english is poor just a little.

I have a DH61WW for a 2 years now,but I never connected a external graphic card.

last week I bought a PowerColor HD 7750 from a friend which perfect working condition,

and connected to my DH61WW but it gave me no signal (blank-black screen since boot cant do anything).I thought my PCI-E x16 slot remain

dust or something,so i cleaned it,and re-seated the card but the problem is still.

BIOS indicate PCI-E x16 slot is empty (not populated)

i spent countless time with this mess and gave up and connected a HD4850 to my DH61WW.

with a big suprise HD4850 working great on my DH61WW and my HD7750 working perfectly on my friend's PC.

now im kind a lost in this issue and dont know what to do.

I have updated to the latest bios (without any single error )

I have followed the removing CMOS battery solution for 1 hour and re connected (out of chassis without power cables)

HD4850 working perfect on DH61WW which means the board have not any fault.

HD7750 working perfect too on my friend's that means the card have not any fault too.

please help guys.... i saw a member of intel community named sylvia_intel is giving options for many issues cant find him or she

my Spex are:

i3 2100 @ 3.10Ghz

DH61WW

Kingston 4GB (2x2GB's) @ 1333Mhz

450 PSU cameup with the casing (you guys calling it chassis)

hi everyone,

hope you'll understand my problem,my english is poor just a little.

I have a DH61WW for a 2 years now,but I never connected a external graphic card.

last week I bought a PowerColor HD7750 from a friend with perfect working condition,

and connected to my DH61WW but it gave me no signal (blank-black screen since boot cant do anything).I thought my PCI-E x16 slot remain

dust or something,so i cleaned it,and re-seated the card but the problem is still.

BIOS indicate PCI-E x16 slot is empty (not populated)

i spent countless time with this mess and gave up and connected a HD4850 to my DH61WW.

with a big suprise HD4850 working great on my DH61WW and my HD7750 working perfectly on my friend's PC.

now im kind a lost in this issue and dont know what to do.

I have updated to the latest bios (without any single error )

I have followed the removing CMOS battery solution for 1 hour and re connected (out of chassis without power cables)

HD4850 working perfect on DH61WW which means the board have not any fault.

HD7750 working perfect too on my friend's that means the card have not any fault too.

please help guys.... i saw a member of intel community named sylvia_intel is giving options for many issues cant find him or she

my Spex are:

i3 2100 @ 3.10Ghz

DH61WW

Kingston 4GB (2x2GB's) @ 1333Mhz

450W PSU cameup with the casing (you guys calling it chassis)

Hello everyone,

I have a DH61WW board with i5-2320 (2nd generation), 8 GB RAM, W7-64bits. I installed the radeon r7 260X (with external power) and the computer does not inicializes and there is no video signal (monitor LED flashing). Removing the graphics card micro operates satisfactorily.

My bios had an old version (v. 20) and updated to v. 35 (still a little old) thinking it might help but the same problem occurs.

The graphics card has not been tested on another computer.

Any tips? tks

Is there any list of intel motherboards which support LVDS? I want to connect motherboard directly to display matrix of notebook

Hello

I just applied the latest BIOS upgrade available for my DB85FL : Intel® Download Center, but right after the successful installation, when the computer boots and I press the F10 key in order to access the boot menu, the list appears with a single element listed in it, usually the network card. Even if I try to boot from USB or from a different drive than the default system drive, the list always displays a random single element, but when I access the BIOS, the drive list shows all the connected drives, including the network card and the USB thumb drives. The F10 boot menu used to work flawlessly before the upgrade, so I don't know if I have to do a downgrade on the BIOS version to get the menu to work properly (I don't know if that downgrade is possible). I've tried everything from enabling and disabling different options in the BIOS settings to unplugging the physical drives but nothing seems to work. I use the boot menu option most of the time because I have different operative systems installed in different drives, so it's really important for me to have it working properly.

This is what I have

Intel DB85FL

8 GB RAM DDR3 1333 MHz

1 TB Drive (Win) SATA3

250 GB Drive (Linux) SATA3

250 GB Drive (Mac -iAtkos-) SATA3

DVD RW Drive (SATA)

Thanks in advance.

Hi all,

I have a mSATA drive on which my virtual machines are running. When under load I regularly receive errors from the drive like the follows:

[Fr Apr 10 10:01:20 2015] ata6.00: exception Emask 0x50 SAct 0x20000 SErr 0x4890800 action 0xe frozen
[Fr Apr 10 10:01:20 2015] ata6.00: irq_stat 0x08400040, interface fatal error, connection status changed
[Fr Apr 10 10:01:20 2015] ata6: SError: { HostInt PHYRdyChg 10B8B LinkSeq DevExch }
[Fr Apr 10 10:01:20 2015] ata6.00: failed command: WRITE FPDMA QUEUED
[Fr Apr 10 10:01:20 2015] ata6.00: cmd 61/40:88:90:29:e9/05:00:09:00:00/40 tag 17 ncq 688128 out
                                   res 40/00:8c:90:29:e9/00:00:09:00:00/40 Emask 0x50 (ATA bus error)
[Fr Apr 10 10:01:20 2015] ata6.00: status: { DRDY }
[Fr Apr 10 10:01:20 2015] ata6: hard resetting link
[Fr Apr 10 10:01:21 2015] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[Fr Apr 10 10:01:21 2015] ata6.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[Fr Apr 10 10:01:21 2015] ata6.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[Fr Apr 10 10:01:21 2015] ata6.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[Fr Apr 10 10:01:21 2015] ata6.00: supports DRM functions and may not be fully accessible
[Fr Apr 10 10:01:21 2015] ata6.00: disabling queued TRIM support
[Fr Apr 10 10:01:21 2015] ata6.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[Fr Apr 10 10:01:21 2015] ata6.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[Fr Apr 10 10:01:21 2015] ata6.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[Fr Apr 10 10:01:21 2015] ata6.00: supports DRM functions and may not be fully accessible
[Fr Apr 10 10:01:21 2015] ata6.00: disabling queued TRIM support
[Fr Apr 10 10:01:21 2015] ata6.00: configured for UDMA/33
[Fr Apr 10 10:01:21 2015] ata6: EH complete

Hello. I bought it on amazon as follows: Intel i7 4770k 3.5 gh ; Intel dz87klt - 75k ; Intel Motherboard Liquid Cooler - BXTS13X Fsp pro aurum 850 w . And other things. When assembling pc , lights up for 2 seconds and off ; and so on until I turn off the power supply . A red LED that indicates that the cpu is hot lights. The probe without devices have the same result Any ideas ?

I bought a dq77kb mainboard and I cannot get to show information on a display.

Also the keyboard numlock led does not light up.

The processor is in the compatible procs list

its a i3-3220T processor. The cpu fan start to run. I have a headset plugged in and I do not hear any beeps

When I remove the memory I hear the 3 beeps.

I can't go to the bios as I can see anything. It appears the usb ports don't get power.

I would try a bios upgrade if I could, but it doesn't get to that stage. So no POST either. Tried clear CMOS with power cable dettached, doesn't help

All of this has also been performed out of the chassis with only one memory card in place, no connections but the power switch. It starts running it gives no unusual led activity and no beeps.

The processor is compatible and I don't have any other processors.

The power is connected externally and it has 90 Watts. It boots up an hp laptop nicely with no issues.

I followed all the troubleshooting steps but don't know what else there is I can do.

I have seen multiple posts regarding similar issues. They have not been answered by Intel here:

Re: DQ77KB No Video

Intel DQ77KB->BTKB34500LT5     AA G81483 501

Intel (BX80637I33220T) i3-3220T (original heatsink)

Corsair (CMSO16GX3M2A1333C9) 16GB (2 x 8 GB) DDR3 1333MHz SODIMM

Power adapter:

90W AC adapter for HP notebooks.

Part Number

Regulatory Model: Series PPP012H-S
HP PART NO: 608428-002
Replace with HP SPARE: 609940-001  A090A00AL-HW01  608428-001

Technical Specification

Input: 100 to 240 V~1.5 A 50 to 60 Hz

Output: 19.0V DC 4.74A 90W MAX

Efficiency Level: V

Connector: 3 pin/grounded, mates with interchangeable cords

i m planning to use dh87RL board & i want to enable RAID0 ARRAY BY USING 3 HARD DISK.  I NEED HDD capacity 750 gb only. kindly suggest me the best sata hdd which will work perfectly with raid0

Hi there, I have an Intel Desktop Board DB75EN BIOS Version 0046 and I am having trouble booting into Windows.  Now I recently updated my BIOS to 0046 and ever since then I can't boot into Windows.  I've tried changing the Boot Order, turning off Optical Drive boot etc and Nothing seems to work.  Now for my Boot drive order i see SATA : Port 6G 0 : Hitachi HDS723020BLA642 : PART 0 : Boot Drive, then I have UEFI : SATA : PORT 6G 0 : Windows Boot Manager : Part 1 : OS Bootloader, then I have SATA : PORT 3 : HL-DT-ST BD-RE WH14NS40, and finally UEFI : SATA : PORT 6G 0 : Hitachi HDS723020BLA642 : Part 1 :OS Bootloader.  Now these options are under boot menu type Advanced.  Under boot menu type nornal the Hard Driver Order is as follows: [P0: Hitachi HDS723020BLA], [], [], [], [], [].  Now I've tried changing the boot order multiple times, but i can't seem to get it to boot to the hard drive.  I do have pictures of my bios, but I can't seem to insert them for some reason.

Brad

Hello

I seem to be having some trouble with my wired network adapter built into my DX58OG motherboard.

I'm on Windows 7 64bit and in Device Manager under Network adapters > Intel(R) 82567LF Gigabit Network Connection I get the message "This device cannot start. (Code 10)".

This happened suddenly earlier today. My PC did crash but this shouldn't have killed the adapter. Anyway I've tried the following:

• Updated driver suggested by http://www.intel.com/p/en_US/support/detect/dsktpboards.
  I installed that and nothing happens. Then tried manually selecting the driver (I've tried EVERY driver with 82567LF in the name) from Window's driver list but still no luck and when using the previous link it says my driver is out of date again.
• Updated BIOS.
  http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=20863&ProdId=3261&lang=eng&OSVersion=Windows%207%20(64-bit)*&DownloadType=BIOS
• Uninstalled/reinstalled device
• Disabled/enabled device
• Ran Microsoft's Fix It program

Nothing seems to work. Do anyone have any ideas?

Thanks

James

I have a DZ77GA-70k MB running Win7-64 and RST Raid-1.

I was troubleshooting another problem and I see this irstrtsv error in the Event Viewer.

"Error: Unable to read LBA sector via passthru. : The request is not supported."

<See attached screen shot of the Event Viewer>

The first 6 irstrtsv errors after system startup are:

"Error: Unable to read LBA sector directly. : The system cannot find the file specified."

Then the balance of the errors have the passthru reference.

My system has been running for over a year (since Jan2013) and this error started on Jan.10, 2014 of this year.

I do not see a performance issue due to the error and the problem I was troubleshooting deals with Windows Backup: VSS, SPP errors when the backup fails to complete.

This irstrtsv error occurs when the system starts, there is a cluster of 6 errors in a few seconds, then repeats every 5 minutes with another cluster of 6 irstrtsv errors and continues until I shut it down.

A couple of days ago I upgraded the RST to the latest driver 12.8.0.1016 and that did not solve the problem.

I don't remember changing the system BIOS or RST configuration or loading any application in January or in or around 1/10/2014.

Any thoughts.

Thanks,

Rod...

recently recieved a new intel DX79SR from an RMA due to my old one going out.  well i installed everything back into it as it was previously and now on top of what appears to be my heatsink(h20 920) going out, my computer is blinking red the WD Fire LED on the motherboard.  i tried reapplying thermal paste checking the temp of the processor to make sure it wasn't overheating and it still does this it was also giving 3 long beeps but i moved the ram around a bit and that fixed the beeps.  i'm actually wondering if the heatsink is the issue or if the motherboard is defective at this point.  also it was odd if i had the memory in certain slots it would read as defective ram but moving them into different slots made it read as functioning. wondering if on top of this WD fire LED blinking if the memory slots themselves aren't defective.

anyways the specs are below

processor: Intel Core i7-3820 Sandy Bridge-E Quad-Core 3.6GHz (3.8GHz Turbo Boost) LGA 2011 130W BX80619i73820 Desktop Processor

Power Supply: XCLIO STABLEPOWER 1000W 1000W ATX CrossFire Ready Active PFC Power Supply

Memory: AVEXIR Core Series 16GB Kit (4 x 4GB) Quad Channel 240-pin DDR3 SDRAM DDR3 2400 (PC3 19200)

video card: PNY VCGGTX670XPB GeForce GTX 670 2GB 256-Bit GDDR5 PCI Express 3.0 x16 HDCP Ready SLI Support Video Card

Heatsink: Antec KUHLER H2O 920 Liquid Cooling System

Hard Drive: Western Digital Red NAS Hard Drive WD30EFRX 3TB IntelliPower 64MB Cache SATA 6.0Gb/s 3.5" NAS Hard Drive

Hello,

I am having a Intel DH55TC motherboard with an i3 processor and WIndows 7 (64bit) Ultimate on my machine. Currently, I am having 8 GB of RAM on my board and it's working perfectly fine.

Now, due to some new requirements, I want to increase my RAM to 12 GB by adding one more 4GB module. After inserting the new RAM making a total of 12 GB, the BIOS is detecting 12GB of RAM but the OS boots up very slowly...taking around 10-15 mins and then it also runs very slow. The moment I reduce the total RAM to anything less than or equal to 8GB, things start running smoothly.

Can anyone please guide me - what should I do next?

Thanks,

Vinay Pugalia

hello I have DP55WG, i7 860, Windows 7x 64, and 2 kingston kvr 1.5v of 4GB and other two same kingston kvr 1.5v but 2GB each one. Total I have 12 GB, my problem is that I can only see 8 GB, I don't now what to do or if this combination can't fit on my mother board, any suggest please?

Thanks in advance!

Hi, I'm not the best at explaining things so please bare with me .

I have an Intel DZ87KLT-75K motherboard which has support for additional USB3.0 ports (obviously) and I have a CoolerMaster HAF X case, which has 2x USB3.0 ports on the front. I have them plugged straight into the correct spot on the motherboard (the blue 20-pin? port), they work all well and good without the USB3.0 drivers but only at USB2.0 speeds (obviously) that's no issue. But when I install the USB3.0 drivers for my board and OS: win7 64-bit this one- (Download Center) they work at full USB3.0 speeds, however, when I have a device plugged into them, there is no option to safely remove the device. It has completely disappeared as though the device is not removable. This is ONLY when the USB3.0 driver are installed. And ONLY with the 2x front USB3.0 ports on the case. All other USB3.0/USB2.0 ports work flawlessly. I have tried using third party safely remove tools, still the devices don't show. Happens with both flash drives and portable HDDs. I tried a fresh installation of Windows, still does the same thing. Took me a while to figure out but after long hours spent of trial and error I have decided it's definitely something to do with the driver itself. I've played around with the settings in device manager/BIOS, still doesn't seem to have an option regarding safely removing media. At first I thought maybe it was a feature of the driver and it just didn't need to be done but after only a few days of using no safely remove and just yanking the drives out after use, I had corrupt data, missing files etc. Maybe there is an option somewhere I have missed that needs to be changed? I don't know.

I have googled so many times and looked all over forums to see if anyone is experiencing the same problem and I cant seem to find any info on this exact problem anywhere so here I am seeking any advice/help to overcome my issue.

If I have left out any vital information that may help please let me know, greatly appreciate any help that may be provided

Thanks.

The  USB 3.0 sockets have never worked on this board when used with Windows 8.1, Please help.

I'm sure like most of you, your USB 3.0 ports are not working under Windows 8.  When I saw the firmware updates dated 5/9/2013, I thought finally.  Well after installing the update I can say they still don't work.  I install both updates, front and rear.  The front update processes fine...and those ports may work, but I don't have them hooked up.  The rear update throws the message Device not found!

Any help to get this working under Windows 8, would be much appreciated.

Regards...

Hi everyone,

I have a pc with DH61CR motherboard, i5-2400, 4GB of RAM. Decided to update bios. Working bios was form year 2010. Express bios flash failed few times, with newest, and few earlier vesions. Decided to flash to next version after curent, working one. Success. Then I flashed one, from Dec 2012. Success. Bios looks different, mouse cursor, etc. Nice... The problem is, that it freezes in first BIOS window, showing Intel logo. If i press F10, i get boot devices list, but after selecting anything, it freezes, only reset helps. Bios update with F7 does not do nothing. Tried resetting BIOS, changing RAM, even CPU, without graphics card - the same. Tried BIOS recovery mode by removing jumper - no image, just cycling between on and off. Is there a way to revive motherboard? I have experience of 10 years of fixing similar issues, but I think only way now is RMA it. Any advice is very welcomed, thanks.